what causes my flourescent lights to take a long time to light?

2 days before Thanksgiving I walked into our laundry to wash my underwear and noticed the light wasn't working.

After a short three-give-and-take phrase (use your imagination) I started to take flashbacks virtually what led to this moment in time.

First, our laundry room light was struggling to turn on for several days prior to this.

So information technology just stopped working altogether.

If you give me 5 minutes I'll evidence you how to fix this and you'll save $75 to $90 by doing information technology yourself. Let's get started!!

Getting Started: How to Check that Your Fluorescent Light Ballast is Cleaved

You'll only need iii kinds of tools for this project:

  • Combination Stripper
  • Screwdrivers
  • Voltage Detector
  • These Amazon links assist support Home Repair Tutor…many thanks for using them

Ane clue that your ballast is the reason for a non-working fluorescent light is the lite bulbs struggle to plough on.

As I said in the intro, we noticed this happening over a three-four week menstruation.

A skilful way to check that your ballast is the culprit is to turn on a voltage detector and hold it adjacent to the wires supplying power to the anchor.

Test Ballast for Power

If power is going into the ballast and none is flowing to the fluorescent light bulbs this is an indicator the anchor is expressionless – unfortunately much like the cool old guy named Blue in Old School (for all you Volition Ferrell fans, Bluish the character dies while, ahem, wrestling!!)

RIP Blue

How to Remove Your Former Anchor and Light

Before doing anything further, turn off the circuit that supplies power to the light.

And then double-check that no electricity is running to the light by using your voltage detector. Many thanks to Marker for reminding me that I forgot to add this SUPER IMPORTANT tip.  But that's why I have corking fans like you who catch my absent-mindedness!!!!

There are only a few screws belongings the ballast to the fluorescent lite.

Remove these screws using a screwdriver just don't toss them in the garbage. Primarily because you may not get news screws with the new ballast.

You can cull to remove the ballast earlier or later yous remove the fluorescent light from the ceiling.

To avert having shattered glass all over the flooring I highly recommend removing the fluorescent light bulbs. They're attached to the anchor and you'll have to disassemble the plug.

Removing Fluorescent Light Bulb

But be careful, as yous'll see in the video I nigh broke the calorie-free seedling during this stride. I'yard such a dummy sometimes.

Just two screws concord the fluorescent light to the junction box. Utilise a screwdriver to loosen these screws and but be aware that the calorie-free will drib slightly from the ceiling.

Junction Box Screws

Slide the light'due south frame and pull it down off the junction box screws.

At this betoken take a pic of the existing wiring. This will requite you a reference and help with wiring the new anchor.

Take a Picture of Wiring

If y'all're not particularly strong or have weak shoulders get a friend or relative to help with this part.

Have them concur the light while you unwire the ballast from the junction box. Or, if you really don't similar electricity or your friend/relative (simply kidding) you can hold the light instead and allow someone else unwire it.

Loosen all the wire nuts. I similar to take apart the blackness or hot wires, then the white or neutral wires, and lastly the footing. It just makes me feel improve to do information technology in this guild.

Pull the ballast wires out from the frame.

That's how unproblematic it is to remove a fluorescent light ballast.

Adding a New Anchor to Your Fluorescent Light

You'll need to take your old ballast with yous to the hardware store. It's a expert idea to call and see if they have the right ballast in stock.

I called around to several places that didn't have the ballast I needed. And in fact, I even so ran into a bit of trouble with the ballast I bought (I explain at the finish of the video).

Place the new ballast on the fluorescent lite's frame and tighten information technology with the screws that yous saved from the former ballast.

New Ballast

Fish the new ballast's black, white, and green wires through the pigsty in the lite.

Go your friend or relative to hold the light while you lot wire it to the junction box. Seriously, I had to call my wife into the laundry room to help. I felt bad that she had to hold the calorie-free upwardly while I fiddled with the wires.

Merely, hey that'due south what marriage is all about — helping each other through DIY sickness or health!!

If you lot have kinked wires similar in the picture below cut them with your combination strippers and strip off 3/four of an inch of the insulation.

Trim Kinked Wires

Wire the new ballast in the aforementioned fashion as the one-time one. This time around I recommend wiring the ground beginning, then neutral (white wire), and lastly the hot wire (black in color).

Twist the wire nut until the connection betwixt the wires from the ceiling and the anchor are secure.

Push all the wires back into the junction box as neatly as possible.

Slide the fluorescent light frame onto the screws y'all left in the junction box. Tighten the screws, add the fluorescent light bulbs, and supervene upon the light shade.

BAM!!!! Y'all're done.

Here'southward my step-by-step video tutorial for your viewing enjoyment. It'll evidence y'all but how easy it is to replace a ballast, or at least I promise so!!

If you can change out a light switch or outlet yous can definitely supercede an onetime ballast that doesn't work.

As I said in the first, you lot'll relieve yourself $75 to $90 doing this set up yourself. Years ago I paid our electrician to do a like fix at a rental and this is how much the fee was.

Rightfully so, too!! Only I like saving money for the grocery list that seems to grow every week.

What's Adjacent

If you're installing other electrical devices we have several tutorials on how to wire a light switch, how to wire a dimmer switch, and how to install GFCI outlets in bathrooms.

If you lot're doing a bathroom remodel and demand help, join one of our online courses – they'll make your bathroom renovation much easier!

Allow me know if you have whatever questions and I'll exercise my best to help.

Thanks as always for reading, watching, and beingness part of our awesome community.

Cheers,

Jeff

Prepare Fluorescent Light Ballasts

fitzgeraldfible1997.blogspot.com

Source: https://homerepairtutor.com/fix-your-fluorescent-light-ballast/

0 Response to "what causes my flourescent lights to take a long time to light?"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel